Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Logo
 
Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Main 2
FAQ

Eavestroughing FAQ's:

1. What are the differences between Aluminum/steel and vinyl eavestroughing?

Aluminum/steel is more durable especially up here in the north, it is also continuous so you have no leaks, and with vinyl you will have leaks at every seam. There is also no gap between the aluminum/steel gutter and the facia board, unlike the vinyl gutters.

2. What causes huge icicles at the edge of the roof even though there is an eavestrough system in place?

Ice will form in winter if you have gutters or not. However, ice is usually the result of poor insulation or ventilation (usually both)

3. How many times a year do you need to clean your eavestroughs?

Plan to clean your gutters at least once a year, more often if the roof is directly beneath trees.

4. How to stop eavestroughs from overflowing?

If your eavestroughs overflow, it may be because they are clogged and need to be cleaned (see above). It is also good to check that they are straight and that there is no damage or sags in them.

5. Do wet leaves stick to leaf guard?

Only temporarily. Just as they may temporarily stick to the hood of your car, leaves and debris that land on the surface of our leaf guard product dry quickly in the sun. And unlike the hood of your car, the surface beneath the wet leaves on your eavestrough is perforated so they dry faster!

Vinyl Decking FAQ's:

1. What is vinyl decking?

It is PVC (poly-vinyl chloride) sheet applied waterproofing membrane (system) that is reinforced with a polyester woven backing for strength in all directions.

2. Where is it used?

Vinyl decking is designed to be used as a waterproofing product that not only protects but enhances the appearance of the surface to which it is applied. Designed to withstand pedestrian traffic and available in a variety of colors, textures and thickness. It can accommodate almost any application including decks, patios, walkways, stairs, hot tub and pool areas etc.

3. How is it installed?

Vinyl decking is fully adhered to most smooth substrates using either a contact or latex adhesive and is overlapped and heat welded at the seams. The vinyl is then mechanically fastened at all perimeters ensuring a total waterproofing system is achieved.

4. Is vinyl decking hot? And is it slippery?

As rule darker colors will retain heat in anything, our vinyl decking colors are designed with this aspect in mind. All vinyl has a textured finish in order to provide a sure footed walking surface. However, anything with ice on it is slippery it is not necessarily the vinyl itself. Just like wood covered in water as well as concrete with water and ice.

5. Can I install it myself?

No. Vinyl decking is installed by a network of fully trained applicators. They are trained in waterproofing techniques and building codes to ensure you are getting the best quality installation available. For this reason we are able to offer the industries best warranty.

6. Can I put deicer on vinyl decking in the winter?

Yes, Rock Salt, Kitty Litter and various other snow-melting chemicals can be used on your vinyl surface. We do caution, however, that you clean the surface thoroughly with soap and water and flushed clear prior to letting the heat of the spring sun "bake" any chemical into the surface.

7. How long will my vinyl deck last?

With proper care and cleaning, your vinyl deck could last up to 15-20 years.

8. Will dogs nails or children's toys damage the decking?

The decking is more durable than a kitchen floor.

9. Why do I have bubbles on my new deck?

Vinyl Deck membranes are adhered to an acceptable substrate with the use of either a water-based latex or solvent based contact adhesive.

Latex adhesives dry by evaporation. This is a natural process that can take several hours to complete. During this time, the membrane slowly bonds to the substrate. Because this process is susceptible to freezing, most contractors will use solvent-based contact adhesive during the winter season.

Contact adhesives dry by “flashing off”. The installation procedure involves applying a thin coating of adhesive to one surface (i.e. top of plywood deck), let dry completely then coating the other surface to be glued (i.e. back of membrane), letting it become tacky and then contacting the two surfaces. The bond strength comes when the molecules of glue physically and chemically mesh together. This is a rapid but not a uniform process. Pockets of still wet solvent adhesive can be trapped under the now partially adhered membrane. These pockets will now take longer to flash off and can cause a “gas bubble” to form.

Many of these gas bubbles will vanish as the adhesive dries. Applying heat to the top of the membrane can temporarily soften Vinyl Deck contact adhesives so the bubble will stick down to the plywood. The solar heat from the sun does this naturally, but this process can take time depending on the season. Other methods are quicker and can often be done by the owner, they include: stepping on the bubble with a slight twist, use a hair dryer set at a medium heat, clothes iron and damp towel slip sheet, or pouring hot water over the bubbles.

Concentrated or too high of a heat setting could glaze the membrane finish. A plastic spreader can be used to evenly force the membrane down.

Only a qualified installer should apply direct heat using a Hot Air Welding Gun or Directional Forced Air Space Heater.

Slideshow - Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Image_1 Slideshow - Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Image_2 Slideshow - Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Image_3 Slideshow - Home Improvement with Eavestroughing, Decks & Rails from Marathon in Prince George BC - Image_4


oberste absolvent brendon babenzien serviert eine reihe von baseball - mtzen aus der wieder auferstandene noah - label.die made in usa kappen sport der marke & # 8217; s ikonographie auf der vorderseite und sind erhältlich in den farben schwarz, rot und pink & marine # 8211; mit einer verstellbaren rcken schließung fr eine vielzahl von kopf, formen und größen.auschecken noah & # 8217;Nike Air Pegasus 89 Tech PRT s neu eröffnete new yorker flaggschiff, während du & # 8217; neu auf.seltsam wird ein pop - up - store eröffnen,ADIDAS NMD R1 diesmal in sydney.TIMBERLAND CHUKKA BOOTSliegt bei 80 oxford street in darlinghurst, der gang wird in der stadt und in diesen tagen wird natrlich auch durch den laden.liful freilassung ein kurzes video fr herbst / winter 2014 mit dem titel & # 8220; mann & # 038; junge #.NIKE LUNAREPIC LOW FLYKNIT 2 & 8221;NIKE ELASTICO PRO III IC wie der name des films, die testperson ist ein junge, der seine umgebung erkundet wird, wächst in männlichkeit in den prozess.das video ist ein faszinierender und faszinierende schau, wie liful & # 8217, kleidungsstcke, mischung und sich im realen leben & # 8212, creative director chanho shin namens der marke liful nach aufsetzen der suffix & # 8220; - #. & 8221; & # 8220;NIKE LEBRON 14 leben und hoffen # 8221; eine marke, die auch bereichert jeden aspekt.Nike Free Flyknit NSWtatsächlich ist ihre herbst / winter 2014 lineup umfasst eine vielzahl von vorlagen,ADIDAS STAN SMITH die sich auf alle teile der mann & # 8217;NIKE AIR MAX 95 CHAUSSURES s lifestyle,TIMBERLAND 6 INCH BOOTS vom sportlichen anoraks und bombenleger jacken fr klassische blazer und trenchcoats. der koreanischen marke wächst exponentiell wie spät, also pass auf mehr kommen. lernen mehr ber liful hier und auf die kurze unten.